Янв 182012
 

 

Features

  • STM32F103VBT6 microcontroller in LQFP100 package (128kB Flash, 20kB SRAM, 2×SPI, 2×I2C, 3×UART, USB, CAN, ADC)
  • Two crystal resonators (8MHz, 32.768kHz)
  • 4-switch keyboard
  • 5-position joystick
  • 8 LEDs
  • Five 16-bit GPIO ports
  • Connector for 2×16 alphanumeric LCD (for example LCD1602)
  • LCD backlight with brighness control (PWM)
  • Digital thermometer TC77 (Microchip) with SPI
  • CAN interface with DB9M connector
  • USB interface (device)
  • Piezoelectric speaker
  • Analog potentiometer
  • 20-pin JTAG connector
  • USB connector for data transmission between PC and STM32 microcontroller
  • SD/MMC connector
  • DB9 connector and RS232 interface
  • Jumpers for boot memory selection
  • Manual PDF zl27arm_en

 

Янв 152012
 

TE-STM32F107 — встраиваемый модуль на основе 32-разрядного микроконтроллера STM32F107 компании STMicroelectronics. Примененный микроконтроллер имеет ядро Cortex-M3, порт Ethernet и два порта CAN. Проверенная схемотехника наиболее сложной части встраиваемой системы, оптимизированная топология платы, наличие функций отладки позволяют использовать модуль TE-STM32F107 как на этапе разработки, так и в составе серийной системы управления.

Особенности:

  • микроконтроллер STM32F107VCT6:
    • 72 МГц Cortex-M3,
    • 256 Кбайт флэш-памяти программ,
    • 64Кбайта ОЗУ,
    • два 12-разрядных АЦП (16 внешних каналов),
    • два 12-разрядных ЦАП,
    • Ethernet MAC 10/100,
    • USB OTG,
    • 2xCAN,
    • 5х USART,
    • 3х SPI,
    • I2C,
    • SDIO,
    • корпус LQFP100;
  • SPI флэш-память AT45DB161D (16 Мбит); 
  • разъем и драйвер порта Ethernet; 
  • разъем порта USB OTG; 
  • 2 разъема и драйверы портов CAN; 
  • 2 разъема порта UART; 
  • разъем JTAG; 
  • аудио-усилитель и динамик; 
  • 31 линия портов микроконтроллера выведена на разъем; 
  • разъем питания +7,5 … 9,0 В; 
  • размеры платы модуля 85х70 мм.

На CD записаны:

  • установочные файлы системы Eclipse/GCC;
  • руководство по ее конфигурации;
  • проект программы тестирования модуля;
  • руководство по использованию этой программы.

Комплектация:

  • плата TE-STM32F107;
  • CD с документацией и программным обеспечением; 
  • руководство пользователя в печатном виде.

Янв 152012
 

 

  • Two power supply options: power connector, USB connector
  • STM32F103RE: high-density performance line ARM-based 32-bit MCU with 256 to 512 kB Flash, USB, CAN, 11 timers, 3 ADCs and 13 communication interfaces
  • LPR430AL: 2-axis gyro (roll, pitch) 300°/s full scale with analog output and optional additional filters
  • LY330ALH: yaw-axis gyro 300°/s full scale with analog output and optional additional filters
  • LSM303DLH: 6-axis geomagnetic module: ±2 g / ±4 g / ±8 g linear acceleration full scale, magnetic field configurable full scale ±1.3 to ± 8.1 Gauss (max), I2C digital output
  • LPS001DL: pressure sensor 300-1100 mbar absolute full scale with I2C digital output and barometer
  • STLM75: temperature sensor with –55 to +125°C range and I2C digital interface
  • Extended connector for wireless connectivity
  • MicroSD™ card slot
  • COM connector with RTS and CTS signals
  • USB 2.0 full speed connection
  • Reset button
  • User LED and button
  • RoHS Compliant
Янв 152012
 

Features:

  • ATmega328 running at 8MHz external resonator (select ‘Arduino Duemilanove w/ 328’ within the Arduino software).
  • Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, Accelerometers, sensors, etc)
  • USB connection off board
  • 3.3V regulator
  • Max 150mA output
  • Over current protected
  • Reverse polarity protected
  • DC input 3.3V up to 12V
  • Resettable fuse prevents damage to board in case of short
  • Power select switch acts as on/off switch

Dimensions: 2.1×2.05″ (53.34×52.08mm)

Documents:

 Posted by at 01:42
Янв 152012
 

Features:

  • 1.95 V to 3.6 V supply voltage
  • 1.6 V to 3.6 V interface voltage
  • ±2g/±4g/±8g dynamically selectable full-scale
  • Output Data Rates (ODR) from 1.56 Hz to 800 Hz
  • 12-bit and 8-bit digital output
  • I2C digital output interface (operates to 2.25 MHz with 4.7 kΩ pullup)
  • Two programmable interrupt pins for six interrupt sources
  • Three embedded channels of motion detection
  • Orientation (Portrait/Landscape) detection with set hysteresis
  • High Pass Filter Data available real-time
  • Current Consumption: 6 μA – 165 μA

Documents:

 Posted by at 01:38
Дек 262011
 
  • 375MHz TI AM1808 ARM926 Microprocessor
  • Onboard 128MByte DDR SDRAM + 128MByte NAND Flash
  • UART, USB, Ethernet, LCD/TSP, SATA, Camera, Audio, TF, JTAG,…
  • Optional WiFi, Camera and 3G Modules
  • Ready-to-Run Linux2.6.33 and WinCE 6.0 OS


Hardware Features

Mechanical Parameters

  • Dimensions: 112.24mm x 82.29mm
  • Working temperature: 0~70 Celsius
  • Input Voltage: +5V
  • Humidity Range: 20% ~ 90%
  • Power Consumption: 0.22A @ 5V (working without LCD)

Processor

  • TI AM1808 ARM9 microprocessor
    — 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation
    — ARM926EJ-S Core
    — ARM9 Memory Architecture
    — Enhanced Direct-Memory-Access Controller 3 (EDMA3)
    — 128K-Byte On-chip Memory
    — 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces)
    — Two External Memory Interfaces
    — Three Configurable 16550 type UART Modules
    — LCD Controller
    — Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects
    — Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces

Memory

  • 128MByte Mobile DDR SDRAM
  • 128MByte NAND Flash (on the rear of the board)

Audio/Video Interfaces

  • Audio input interface (Mic In)
  • Two-channel Audio output interface (Line Out)
  • Two Camera interfaces (30-pin FPC connector on the rear of the board, supports CCD or CMOS camera)
  • LCD/Touch Screen interface (50-pin FPC connector, support resolution up to 2048*2048)

Data Transfer Interfaces and Other Facilities

  • 1 x 5 line Debug serial port, RS232 voltage (brings out by DB9 connector)
  • 2 x 3 line serial ports, TTL voltage (brings out by extension connector)
  • 1 x USB2.0 OTG port, High-speed (Mini USB type)
  • 1 x USB1.1 Host port, Full-speed (USB-A type)
  • 1 x TF card slot
  • 1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)
  • 1 x 10/100Mbps Ethernet interface (RJ45 connector)
  • Battery backed RTC (User needs to prepare battery himself, CR1220 model is ok)
  • 1 x RESET button
  • 1 x BACK button
  • 1 x HOME button
  • 1 x MENU button
  • 1 x 14-pin JTAG connector (for using TI’s XDS100v2 Emulator)
  • 2 x 40-pin extension connectors (SPI, I2C, McBSP, UART, 1.8V, 3.3V, 5V, GPIO are brought out from these connectors)

Дек 222011
 

WT21 is intended at Bluetooth applications where a host processor is capable of running the Bluetooth software stack. WT21 only implements the low level Bluetooth Host Controller Interface (HCI) but still offers advantages of a module — easy implementation and certifications.

Key Features:

  • Highly integrated and cost effective Bluetooth HCI module
  • Bluetooth class 1 radio based on CSR’s BlueCore-6
  • Transmit power 6dBm, receiver sensitivity -87dB
  • Integrated antenna or RF pin
  • Small size: 17,1 x 11,6 x 2,6mm
  • Bluetooth 2.1 + EDR Compliant
  • Bluetooth controller subsystem CE, FCC and IC qualified
  • Industrial temperature range from -40C to +85C
  • 801.11 co-existence interface
  • AuriStream baseband codec, which provides better audio quality
  • Supports any Bluetooth stack with HCI interface

Description

WT21 is intendend for Bluetooth applications where a host processor is capable of running the Bluetooth software stack. WT21 only implements the low level Bluetooth Host Controller Interface (HCI) but still offers advantages of a module- easy implementation and certifications. WT21 is based on CSR’s BlueCore-6 chip and offers the lowest current consumption and the highest integration level in its class. WT21 supports Bluetooth 2.1 + EDR standard. It also has AudiStream technology built in, which significantly improves the quality of voicein audio applications.

WT21 supports any Bluetooth software stack that implements the standard Bluetooth HCI interface. The software stack can interface to the module either via UART, SDIO or SPI interface. WT21 offers Bluetooth
in integrated form factor that is easy to understand, manage and source. It is an ideal product for an OEM who does not want to spend significant amount of time and money to RF regulatory approvals and designing a complex 2,4 GHz radio product. By utilizing Bluegiga’s world-class integration services and technical support, OEMs can beassured that their products reach the market quickly and cost efficiently.

http://www.bluegiga.com/WT21_Bluetooth_HCI_Module

 

 Posted by at 20:53
Дек 222011
 

  •  Bluetooth protocal:  Bluetooth Specification v2.0+EDR
  •  Frequency:  2.4GHz ISM band
  •  Modulation:  GFSK(Gaussian Frequency Shift Keying)
  •  Emission power:  ≤4dBm, Class 2
  •  Sensitivity:  ≤-84dBm at 0.1% BER
  •  Speed: Asynchronous:  2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
  •  Security:  Authentication and encryption
  •  Profiles:  Bluetooth serial port
Power supply: +3.3VDC 50mA
Working temperature: -20 ~ +75 Centigrade
Dimension: 26.9mm x 13mm x 2.2 mm
[wpfilebase tag=file id=1 /]
Bluetooth-модуль HC-05
 Posted by at 20:47